KELLY-MOORE PAINT CO INC -- ACRY-SHIELD ACRYLIC FLAT FINISH, 1240-SERIE  -- 8010-00N022019
<pre>=====================  Product Identification  =====================

Product ID:ACRY-SHIELD ACRYLIC FLAT FINISH, 1240-SERIE
MSDS Date:06/30/1989
FSC:8010
NIIN:00N022019
=== Responsible Party ===
Company Name:KELLY-MOORE PAINT CO INC
Address:1015 COMMERCIAL ST
City:SAN CARLOS
State:CA
ZIP:94070
Country:US
Info Phone Num:415-592-8337
Emergency Phone Num:800-424-9300(CHEMTREC)
Preparer's Name:JULIAN SCHAFER
CAGE:KELLY
=== Contractor Identification ===
Company Name:KELLY-MOORE PAINT CO INC
Address:1015 COMMERCIAL ST
City:SAN CARLOS
State:CA
ZIP:94070
Country:US
Phone:415-592-8337
CAGE:KELLY

=============  Composition/Information on Ingredients  =============

Ingred Name:ETHYLENE GLYCOL  (SARA III)
CAS:107-21-1
RTECS #:KW2975000
Fraction by Wt: <4%
OSHA PEL:C 50 PPM
ACGIH TLV:C 50 PPM,VAPOR; 9192
EPA Rpt Qty:1 LB
DOT Rpt Qty:1 LB

Ingred Name:PROPIONIC ACID, 2-METHYL-,MONOESTER
    W/2,2,4-TRIMETHYL-1,3-PENTANEDIOL; (TEXANOL). VP: 0.04@68F
CAS:25265-77-4
Fraction by Wt: <5%

=====================  Hazards Identification  =====================

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES  Skin:YES  Ingestion:YES
Reports of Carcinogenicity:NTP:NO    IARC:NO	OSHA:NO
Health Hazards Acute and Chronic:ACUTE: DIZZINESS, HEADACHE, NAUSEA,
    CONFUSION, IRRITATION TO UPPER RESPIRATORY TRACT, UNCON, SKIN AND
    EYES IRRITATION. CHRONIC: NONE KNOWN.
Explanation of Carcinogenicity:NOT RELEVANT.
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:SEE YOUR PHYS FOR SPECIFIC MED
    OPINION REGARDING YOUR CONDITION.

=======================  First Aid Measures  =======================

First Aid:INHAL: REMOVE TO FRESH AIR. RESTORE BREATHING. CONSULT PHYS.
    EYE: FLUSH WITH LARGE VOLUMES OF WATER FOR AT LEAST 15 MIN. GET MED
    ATTN. SKIN: WIPE OFF WITH A RAG. WASH THOROUGHLY WITH SOAP AND
    WATER. I NGEST: CONSULT HOSPITAL EMERGENCY ROOM OR POISON CONTROL
    CENTER IMMED.

=====================  Fire Fighting Measures  =====================

Flash Point:>200F,>93C
Extinguishing Media:NOT APPLICABLE. MEDIA SUITABLE FOR SURROUNDING FIRE
    .
Fire Fighting Procedures:NONE. WEAR NIOSH/MSHA APPROVED SCBA AND FULL
    PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:CLOSED CONTAINERS MAY EXPLODE (DUE TO
    BUILDUP OF STEAM PRESSURE) WHEN EXPOSED TO EXTREME HEAT.

==================  Accidental Release Measures  ==================

Spill Release Procedures:VENTILATE AREA TO PREVENT BUILDUP OF VAPORS.
    FOR SMALL SPILLS, SOAK UP WITH ABSORBANT. FOR LARGER SPILLS, DIKE
    AREA WITH ABSORBENT MATERIAL AND SCOOP UP LIQUIDS.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

======================	Handling and Storage  ======================

Handling and Storage Precautions:STORE UPRIGHT IN SEALED CONTAINERS
    AWAY FROM HEAT AND FLAME.
Other Precautions:REMOVE AND WASH CONTAMINATED CLOTHING BEFORE REUSE.

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:USE NIOSH/MSHA APPRVD PARTICLE MASK TO AVOID
    BRTHG SPRAY MIST OR SANDING DUST IF LOC VENT IS ADEQ TO KEEP TLV
    W/IN ACCEPTABLE LIMITS. IF LOC VENT IS NOT ADEQ, THE USE OF AN
    NIOSH/MSHA APPRVD RESP FOR	ORG VAP, SUPPLIED AIR OR SCBA IS RECOM.
Ventilation:LOCAL EXHAUST SUFFICIENT TO KEEP TLV BELOW PRESCRIBED
    LIMITS.
Protective Gloves:RECOMMENDED.
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:NONE SPECIFIED BY MANUFACTURER.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
MFR TRADE NAME/PART NO: ALL COLORS.

==================  Physical/Chemical Properties  ==================

HCC:N1
Boiling Pt:B.P. Text:212F,100C
Vapor Pres:SEE INGRED
Vapor Density:<AIR
Evaporation Rate &amp; Reference:SLOWER THAN ETHER
Appearance and Odor:NONE SPECIFIED BY MANUFACTURER.
Percent Volatiles by Volume:52-62

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS.
Hazardous Decomposition Products:MAY PRODUCE HAZARDOUS FUMES WHEN
    HEATED TO DECOMPOSITION AS IN WELDING.

====================  Disposal Considerations  ====================

Waste Disposal Methods:DISCARD IN LANDFILL IN SEALED METAL CONTAINERS
    AWAY FROM HEAT AND FLAME AND IN ACCORDANCE WITH LOCAL, FEDERAL, AND
    STATE REGULATIONS.

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.